Zilog Z8F0130 Manuel d'utilisateur télécharger pdf

www.zilog.com

Introduction

Zilog’s Ethernet Smart Cable, part number ZENETSC0100ZACG, allows you to connect

Z8 Encore!

, Z8 Encore! XP

, ZNEO

™

and eZ80Acclaim!

development boards to a

Zilog Developer Studio II (ZDS II) host system using an Ethernet connection.

This user manual provides instructions for installing the Ethernet Smart Cable hardware.

Instructions are also provided for Ethernet-equipped host PCs that are not network-con-

nected. After the Ethernet Smart Cable is connected, proceed with debugging as described

in the documentation specific to your development kit.

Kit Contents

To determine the contents of your kit, refer to the Ethernet Smart Cable Packing List

(PAK0019), a paper insert included with your kit.

Software and Hardware Requirements

The requirements for using the Ethernet Smart Cable are:

• A host PC with ZDS II v4.10.0 or later for Z8 Encore!, eZ80Acclaim!, or ZNEO. To

determine ZDS II requirements for your host system, refer to the quick start guide for

your specific development kit. The latest version of ZDS II is available as a free down-

load from the Zilog Store

• An available 10/100 Mbps Ethernet connection.

If you are using ZDS II – eZ80Acclaim! versions earlier than 4.10.0, see the

Using the Ethernet Smart Cable on ZDS II – eZ80Acclaim! Versions Earlier

than 4.10.0 section on page 11.

Note:

Ethernet Smart Cable

User Manual

UM020705-1012

1 2 3 4 5 6 ... 12 13

Résumé du contenu

Page 1 - Ethernet Smart Cable

Page 2 - Supported Target Environments

Ethernet Smart CableUser ManualUM020705-1012 Page 10 of 133. After the configuration in the Settings tab are changed, click the Submit button. A messa

Page 3 - Network

Ethernet Smart CableUser ManualUM020705-1012 Page 11 of 13Connecting to the Target BoardAttach one end of the six-conductor ribbon cable to the Smart

Page 4 - UM020705-1012 Page 4 of 13

Ethernet Smart CableUser ManualUM020705-1012 Page 12 of 134. Note the IP Address. If you have several Ethernet Smart Cables connected to the net-work,

Page 5 - UM020705-1012 Page 5 of 13

Ethernet Smart CableUser ManualUM020705-1012 Page 13 of 13DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.LIFE SUPPORT POLICYZILOG'S PRODUCTS ARE

Page 6 - UM020705-1012 Page 6 of 13

Ethernet Smart CableUser ManualUM020705-1012 Page 2 of 13Supported Target EnvironmentsThe supported target environments are described in the following

Page 7 - dialog box will appear

Ethernet Smart CableUser ManualUM020705-1012 Page 3 of 13Connecting the Ethernet Smart Cable to a DHCP-Based Network The following considerations must

Page 8 - UM020705-1012 Page 8 of 13

Ethernet Smart CableUser ManualUM020705-1012 Page 4 of 133. Launch ZDS II.4. Navigate via the File menu in ZDS II to open one of the projects listed i

Page 9 - UM020705-1012 Page 9 of 13

Ethernet Smart CableUser ManualUM020705-1012 Page 5 of 132. Use the Ethernet crossover cable supplied with the Ethernet Smart Cable to connect the Eth

Page 10 - User Manual

Ethernet Smart CableUser ManualUM020705-1012 Page 6 of 135. In the panel labeled LAN or High-Speed Internet, double-click the Local Area Con-nection i

Page 11

Ethernet Smart CableUser ManualUM020705-1012 Page 7 of 137. In the panel labeled This connection uses the following items:, select the Internet Protoc

Page 12 - Troubleshooting Tips

Ethernet Smart CableUser ManualUM020705-1012 Page 8 of 138. Enter an IP address of 192.168.1.21 and a subnet mask of 255.255.255.0. These values place

Page 13

Ethernet Smart CableUser ManualUM020705-1012 Page 9 of 13cable’s IP address, which can be obtained from ZDS II in the ZDS II Project Settings win-dow;